The doors of the closet with their own hands. How to assemble and install sliding doors for the closet with your own hands? Mounting the doors of the closet with your own hands
In order to save some people start to dofurniture yourself. For example, if you purchase material and accessories, you can get an inexpensive cabinet with sliding doors. Today such products are in great demand, since they save a living space, are convenient to use, they decorate the interior (it concerns models with an original and interesting view). The following describes how to prepare and mount the doors of the closet with your own hands, and also decorate them unusually.
Before embarking on production work,It is necessary to understand which constructions are generally available. Coupe doors are equipped with a suspension system, an overhead or frame profile. Suspended products are considered to be the cheapest, because they consist of a blade of particleboard and a cladding edge. On its inner side there are rollers at the top, and at the bottom are guiding elements. Such a system is difficult to adjust, quickly fails, and the cloth is prone to bending.
Overhead profiles better retain chipboard, becausethey are located on each side. If you need these doors of the closet with your own hands, then the lower rollers equipped with bearings will act as a support. In the upper part, there are also rollers, but they perform the support function. If there is an obstacle in the way of the doors, they can skew and jump out of the grooves.
The frame profile is a constructionfrom horizontal and vertical elements. They are made of steel (aluminum) and make the product more durable and reliable. Rollers on the doors move not only to the sides, but also vertically. A glass or a mirror can easily be inserted into the canvas.
To make furniture look neat, you needcorrectly measure the door of the closet. With their own hands make them a width of 500-1000 mm. Too small a door will collapse, but too much is difficult to operate. The height of the structure depends on the type of profiles. For example, the overlaid elements have a length of 5500 mm, so they can be adjusted in height.
When calculating the width of doors,overlapping. Therefore, the width of the profile is added to the measurement of the opening, and the total amount is divided into two (the number of canvases). If there are more doors, the number of profiles will increase.
The height of the door-coupe is calculated much easier: you need to measure the opening in height and subtract from it 45 mm. This distance allows you to put the canvas in the upper profile. Do not subtract less than 45 mm, otherwise the doors will get stiff.
How to make the doors of the closet with your own hands andwhat material should I use for this? His choice depends on the financial abilities and design preferences of the consumer. Most often in the calculation take chipboard, glass, mirrors, plastic, etc. Doors from the chipboard imitate the natural material, make the interior homely, warm and interesting. They are used in the manufacture of budget cabinets, because they have a low cost.
Glass structures can be: matt, patterned, colored or embossed. They are pasted with a special film, which, when impacted, will not allow the material to break into small pieces. Mirror doors also look very exquisite. They can be tinted, covered with anti-reflective film, equipped with built-in lamps, patterns and patterns.
Quite often there are doors made of acrylicplastic - very durable material. Its color palette is diverse, which allows you to create an individual design. You can get a unique interior if you combine this design with the decoration and other interior details.
Fasteners and guides
You can install the doors of the closet with your own hands,if you buy the necessary fasteners (rollers, screws, adjusting screws, guides, etc.). The bulk of their weight falls on the bottom, so there should be a large rollers. The upper rollers are small in size, because they are only needed to support the structure and move along the guide profile. Adjustment screws with fine threads, which are responsible for the slope of the doors, will also be needed. The main fasteners are self-tapping screws, which connect the elements into a single product.
For moving the doors inside the cabinet answerhorizontal guides. The top profile is a horizontal part at the top of the door frame, which has a filling in the form of a chipboard or a mirror. A special groove for screwing self-tapping passes along it. With the help of the lower guide element the vertical profile is fixed, the carrier rolls are concealed, the appearance improves.
It will not be possible to make sliding doors forwardrobe with their own hands without a vertical profile-handle. On it there is a groove into which the filling is inserted. This element makes the product attractive, because it looks very elegant.
After taking measurements, selecting materials andThe accessories begin to assemble the doors. First prepare the filler. Exactly along the perimeter, a silicone sealant is laid. Then it is applied to the main material and attached to it from above and from below by horizontal slats. It is very important that the mirror goes into all the grooves, and the sealant is not visible.
When manufacturing the door of the closet with your own handsalso perform the alignment of the side racks. For this, the design is placed on the edge and put them on the mirror. Elements of profiles are fastened together by self-tapping screws, for which pre-prepared holes are needed. After that, rollers are installed at the top and bottom, and a tape with a pile is glued to the vertical profiles. If necessary, the design is equipped with handles (screwed with screws or inserted into the cut hole).
Before assembling the doors of the sliding door wardrobewith their own hands, perform the preparation of the opening. To begin with, the horizontal and evenness of the guides is checked. The entire structure must have a strict geometry, but small errors are hidden in the process of adjusting the doors. You can also align the cabinet using the tuning legs (especially if the floor has irregularities).
If you want to mount a built-in cabinet, thenwill have to prepare an opening. To begin with, measure its width again and cut out of the chipboard two pads. Their size should coincide with the width of the opening (maximum accuracy is required). With the help of a drill, several holes are made in them. Lining is applied to the ceiling, leveled and attracted by screws so that they are imprinted. In the designated places holes are drilled and dowels are blocked. The details cut from the chipboard are screwed with screws. The lower lining is mounted in the same way as the upper lining. It is very important that it is perfectly even.
Installing the doors in the closet with your own handsbegins with the laying of guides. First take the top element, measure the desired length and jigsaw cut off excess. The same is done with the lower guide element. With the help of a drill, drill the holes necessary for fixing to the cabinet parts or linings. The guides are applied, leveled and fixed with screws.
Once everything is finished, you can proceedto the installation of doors. The first sheet is inserted into the guides, the system is operable and adjustment is performed. Correctly adjusted doors will allow the mechanisms to work quickly and easily. After that, install the second cloth, check and adjust it. Sometimes install three-leaf sliding doors for the closet with their own hands. Then the assembled shutters push back and mount the third sheet. With him, all the same manipulations are carried out as with the previous elements.
At any time, you can remove the doors and decorate them with different materials. In this case, you can choose: mirrors, patterned glass, leather and fur, various films.
1. The mirror is very often inserted into the doors of the wardrobes, especially if the furniture is located in the hallway. Silver and bronze products are best for interior decoration.
2. Patterned or ordinary glass, covered with decorative film, looks great on furniture designs. Individuality will be given to the room by custom-made material.
3. Photo printing looks very nice and allows you to create absolutely any image. In this case, the picture is applied either directly to the surface, or to a film that is glued under the glass.
4. Decorating the door with the help of leather and fur. Today, decorative panels imitating the skin and fur of animals are in great demand. If desired, they are applied various drawings and patterns.
5. Special films allow you to quickly and cheaply decorate the product. A variety of colors and textures will help to combine furniture with any style of interior.
The closet is popular with consumersthanks to its spaciousness, space saving and attractive appearance. It will cost less if you figure out how to assemble the doors of the closet with your own hands. And if the apartment has a roomy niche, then you can protect it and get an excellent dressing room.